Rubber

Jiangsu Feiya Chemical Corporation Co. Ltd Products

Polymer of 2,2,4-trimethyl-1,2-dihydroquinoline TMQ belongs to a group of slightly staining, stearically hindered amines

TMQ is a highly effective agent that prevents heat-induced aging and also provides minor protection against ozone and fatigue crack failure. Its major field of application is with black elastomer based on SBR. NR, IR, BR and NBR . It provides excellent heat resistance in peroxide cured NBR and EPDM. It is also used in polyethylene that has been cross-linked with peroxide.

Moulded, Extruded, Calendered

Jiangsu Feiya Chemical Corporation Co. Ltd Products

Butylated reaction products of p-cresol and dicyclopentadiene Antioxidant 616 is a highly effective polyphenolic additive with high activity and very low volatility

Antioxidant 616 is non-discolouring and non-pinking. Antioxidant 616 is especially recommended for the protection of natural and synthetic polymers based on isoprene and butadiene chemistry. Antioxidant 616 is ideally suited for the protection of light coloured, non-staining goods derived from natural rubber and latex, SBR and carboxylated SBR latices, ABS, NBR, BR, SBS and SIS in applications where the retention of appearance and elastic properties during storage and use are important requirements.

Moulded, Extruded, Calendered

Jiangsu Feiya Chemical Corporation Co. Ltd Products

4,4-Bis(alpha,alpha-dimethylbenzyl)diphenylamine An amine type antioxidant which is relatively non-discoloring and effective against heat deterioration of NR and synthetic rubbers such as EP, EPDM & CR

It exibits excellent heat resistant effect for nylon 6, ABS resins, polyolefins, synthetic lubricant oil, polyether polyols, and hot-melt adhesives

Moulded, Extruded, Calendered

Jiangsu Feiya Chemical Corporation Co. Ltd Products

Reaction product of Diphenlylamine and Alpha-Methyl Styrene Antioxidant KY-86 is antidegradant for universal application especially for rubber goods based on CR as well as on NR,IR,BR.SBR.NBR.EPDM and their combinations

It protects effectively and for a long time against influences of oxygen,heat and dynamic fatigue action. It provides also good protection against rubber poisons. The vulcanizates are being coloured by light influence just very slightly,therefore it is possible to use it in light compounds. It does not cause contact colouring. KY-86 does not bloom even at high dosage. It does not influence the basic physico-mechanical properties of vulcanizates. Its volatility is very low. Antidegradation effectiveness can be significantly increased by combination with imidazoles,phenols or phosphites(heat and thermo-oxidative resistance)or p-phenylenediamines(ozone resistance). KY-86 is also applicable as stabilizer for plastics,lubricants,oils and other substrates

Moulded, Extruded, Calendered

Jiangsu Feiya Chemical Corporation Co. Ltd Products

Pentaerythrityle Tetrak-is[β--(3.5 di tert butyl 4 hydroxyphenyl) propionate] The product is white crystalline powder, soluble in such organic solvents as benzene, toluene, chloroform and so on, slightly soluble in alcohol, but insoluble in water.

The product is the typical representative of hindered phenol antioxidants, non poisonous, nondiscolouring as well as nonstaining and is an excellent top quality approved in international market. It is widely used in a variety of polymer materials, such as polypropylene, polyethylene, polyester, polyurethane, polystyrene, polyxymethylene, PBT, ABS, polyamide, synthetic rubber and so on. It is also a high grade antioxidant for natural and synthetic oil.

Moulded, Extruded, Calendered

Aquaspersion Ltd Products

LUVOMAXX ZBEC acts as an ultra-accelerator, suitable for NR, SBR, IIR, EPDM, less suitable for CR. LUVOMAXX ZBEC exhibits most delayed action compared to other dithiocarbamates, thus improving processing safety.

High crosslinking levels will be achieved already at moderate curing temperatures LUVOMAXX ZBEC is used as primary accelerator or as secondary accelerator for thiazoles. Addition of zinc oxide as well as of sulphur is required.

Moulded, Extruded, Calendered

Lehmann & Voss & Co Products

LUVOMAXX TAC DL 70 is a versatile co-agent for peroxide or radiation crosslinking of high-Mw-polyolefins and synthetic rubbers. Especially applied for cable jackets, cable insulating compounds and heat resistant rubber articles

LUVOMAXX TAC DL 70 in elastomers and plastics increases the efficiency of the radical source (e.g. peroxide savings are possible), providing for increased crosslinking density, better mechanical properties, improved compression set of the vulcanisates.

Moulded, Extruded, Calendered

Lehmann & Voss & Co Products

LUVOMAXX LNBR N280 DL 70 is a dry liquid preparation of a low-volatile, cross-linkable polymeric plasticizer, mainly applied in NBR compounds with demands for low compression set and low migration properties During vulcanisation the active ingredient LNBR N280 gets grafted to the main-elastomer backbone via sulphur crosslinks. After vulcanisation the formerly mobile plasticizer is now a fixed part of the polymer matrix and shows neither any migration tendencies nor can be extracted.

The use of LUVOMAXX LNBR N280 DL 70 avoids extensive thermo-conditioning steps and material losses of the high viscous, sticky liquid plasticizer. The free-flowing, non-dusting DL powder can be properly weighed and handled and provides for consistent dosage batch-by-batch and allows a best-possible dispersion of its pre-dispersed liquid active ingredient. LUVOMAXX LNBR N280 DL 70 is particularly recommended for the usage in NBR compounds but it is also applicable within other polar (diene) rubbers like CR.

Moulded, Extruded, Calendered

Lehmann & Voss & Co Products

LUVOMAXX DPTT Pellets act as ultra-accelerator and sulfur donor for NR, SBR, BR, NBR, providing for good ageing characteristics of the vulcanisate

Mainly used as secondary accelerator in combination with mercapto accelerator types, LUVOMAXX DPTT Pellets are very active above 110°C, recommended vulcanization temperature range: 100°C – 150°C.

Moulded, Extruded, Calendered

DOG Products

Homogenisator 501D improves the homogeneity of rubber blends of polymers with different polarities and viscosities

Improves the homogeneous blending of polymers with different polarities Optimized dispersion and processing behavior Increased tack, Economical product with a distinctly darker color

Moulded, Extruded, Calendered

DOG Products

Homogenisator 501 improves the homogeneity of rubber blends of polymers with different polarities and viscosities. It imparts better building tack to raw compounds and facilitates processing during mixing, extruding and calendering

Improves the homogeneous blending of polymers with different polarities Optimized dispersion and processing behavior Increased tack

Moulded, Extruded, Calendered

DOG Products

Dispergum ZK is a combination of zinc and potassium soaps, which has a positive influence on the dispersion of light fillers and carbon black. It enables excellent and effective dispersion of even high quantities of mineral fillers. The mixing time can be reduced. It is suitable for all standard elastomers such as NR, SBR, EPDM and NBR. The flowability of rubber compounds is improved, as well as the filling of small cavities during the moulding process.

Effective for compounds with light fillers Improves filler dispersion and reduces reagglomeration, Improves flow behavior, BFR / FDA suitable

Moulded, Extruded, Calendered

DOG Products

Dispergum PT is a concentrated combination of zinc salts of saturated and unsaturated fatty acids. Dispergum PT acts as lubricant and shows a reducing effect on compound viscosity. Therefore Dispergum PT performs energy saving and improves the dispersion of filler and other ingredients.

Reduces viscosity / better flow behaviour Improves filler dispersion, Positive influcence on heat build-up, BFR / FDA suitable

Moulded, Extruded, Calendered

DOG Products

Dispergum E is a processing additive which acts as lubricant and shows a reducing effect on viscosity. It facilitates mixing and processing, energy can be saved by a cooler mixing process and lower viscosities. As an additonal effect the dispersion of fillers and other ingredients is improved in NR, SBR and NBR compounds

Low dropping point, Suitable for one step and open mill mixing Improves filler dispersion, BFR / FDA suitable

Moulded, Extruded, Calendered

DOG Products

Due to its solubility in rubber, Dispergum 36 incorporates and disperses with exceptional ease and rapidity. It can be used for NR and SR over a wide temperature range on open mills and in internal mixers. Mastication times are dramatically reduced by Dispergum 36 due to high efficiency of the oxidation catalyst. It is not classified as hazardous material. It does not contain DBD or PCTP

Highly efficient at low dosages, Low dropping point, Fast dispersion

Moulded, Extruded, Calendered

DOG Products

In diene rubber, dithiophosphates generate a short flow period and vulcanization time similar to dithiocarbamates. It may be combined with all common accelerators. In Deovulc TP 4-75, the liquid zinc dialkyldithiophosphates are absorbed on highly dispersible silica for better handling

Nitrosamine free, For rapid vulcanization, particularly as a primary accelerator for EPDM High solubility, no blooming, Non staining, therefore also particularly suitable for light compounds, Reversion stabilizer for NR, in combination with thiazole or sulphenamide accelerators

Moulded, Extruded, Calendered

DOG Products

Deovulc OH is used as an acid scavenger and crosslinking activator in fluorocarbon polymers. The fineness of Deovulc OH provides high activation and spotless dispersion

Cross linking activator and acid scavenger for FKM, Fine powder for a spotless incorporation, BfR / FDA suitable

Moulded, Extruded, Calendered

DOG Products

70% hexamethylene diamine carbamate in AEM master batch

Amine accelerator for AEM and HT-ACM, Soft granules for a dust- and speck free incorporation, Hydrolysis protection through the polymer carrier system

Moulded, Extruded, Calendered

DOG Products

Deovulc EG 3 MF is a fast curing primary accelerator blend for EPDM with freedom from blooming and staining. It replaces complex accelerator combinations in EPDM and enables good heat resistance and a low compression set

Free of ETU, Ready to use, No blooming

Moulded, Extruded, Calendered

DOG Products

Deovulc EG 3 is a blend of accelerators. This prevents blooming in sulphur cured EPDM rubber.

Versatile areas of application, Fast vulcanization, Bloom free

Moulded, Extruded, Calendered

DOG Products

Deovulc BG 187 V is a blend of accelerators, which cannot form any nitrosable secondary amines

Does not form toxic nitrosamines, Balanced vulcanization characteristics, Good solubility in the polymer and hence bloom free

Moulded, Extruded, Calendered

DOG Products

Deotack RS gives rubber compounds an excellent / special building tack, which stays on the same high level for many improved days. With partial co-vulcanization improved physical properties can be reached

Excellent tackifying resin, High building tack over a long period

Moulded, Extruded, Calendered

DOG Products

Deotack 70 DL increases building tack of compounds with low own tack. Deotack 70 DL facilitates processing of synthetic rubber compounds and provides a better dispersion of carbon black and light active fillers

Dry liquid of Deotack P, Easier weighing / handling, Particularly suitable for soft compounds or open rolling mill mixing

Moulded, Extruded, Calendered

DOG Products

Deotack 1100 is a tackifing resin with an excellent compatibility in different polymers and bonding agents. The product is of a light colour and neutral odour

Homogenizing and tackifying resin, Light color and neutral odor, No PAH, FDA suitable

Moulded, Extruded, Calendered

DOG Products

The sulphur particles in Deosulf L 95 are coated with dispersing agents. By this formation of agglomerates during storage, transporting and incorporating as well as dusting is avoided. Furthermore the sulphur preparation is readily incorporated and uniformly dispersed. No local overcure appears and consequently vulcanisates with excellent ageing properties are obtained

Readily dispersed, Dust-free incorporation, Reduction of local overconcentration, enables uniform physical properties, BFR / FDA suitable

Moulded, Extruded, Calendered

DOG Products

Due to its bifunctionality Deolink TESPT-100 links through the tetrasulfane group to the rubber molecule and through the ethoxy group to the silanol groups of the filler. The chemical bond between polymer and filler improves the physical properties of the compound

Sulphur silane most commonly used, Improved mechanical properties such as abrasion or compression set, Optimum silanization at a mixing temperature between 130 – 150°C

Moulded, Extruded, Calendered

DOG Products

Due to its bifunctionality Deolink TESPT links through the tetrasulfane group to the rubber molecule and through the ethoxy group to the silanol groups of the filler. The chemical bond between polymer and filler improves the physical properties of the compound

Sulphur silane most commonly used Improved mechanical, properties such as abrasion or compression set, Optimum silanization at a mixing temperature between 130 – 150°C

Moulded, Extruded, Calendered

DOG Products

Deolink Vinyl-100 forms a chemical bond between rubber molecule and the silica filler. The methoxyethanol, which is formed owing to the reaction evaporates during the mixing and vulcanization process

Traditional vinyl silane, For radical cross-linking

Moulded, Extruded, Calendered

DOG Products

Deolink Methacryl TM-100 reacts with unsaturated polyesters, polyurethanes and acrylic resins. The tri-ethoxy-silyl group condenses with the hydroxyl groups / other reactive groups of various substrates and links them to the polymer.

Suitable for radical as well as for sulphur cross-linking systems, BfR suitable

Moulded, Extruded, Calendered

DOG Products

Deolink Mercapto TM-100 is a bifunctional coupling agent, which can be used in various applications to improve the bonding between the inorganic substrate or filler and the organic polymer. Deolink Mercapto TM-100 can increase the mechanical properties like the adhesion to the surface or abrasion resistance. Furthermore the dispersion in the polymer matrix of inorganic pigments and filler can be increased.

Gives excellent results in CR.

Moulded, Extruded, Calendered

DOG Products

The amino group of Deolink Amino TE-100 can react with various polymers. Therefore it is used for surface coatings and sealing materials as well as for polymer compounds. If it is used in glass fibre reinforced nylon, polyester ot other resins, it can increase the mechanical properties of the finished article. The dispersion of the inorganic fillers in the polymer matrix can be increased decisively

For sulphur free cross-linking systems, BfR suitable, Predominantly for ACM and AEM compounds with light fillers

Moulded, Extruded, Calendered

DOG Products

Deostab N improves the state of cure and the compression set by reducing the negative influence of CaO in the vulcanization characteristic without affecting the desiccant action of calcium oxide

Primarily for EPDM profile compounds, BfR suitable, No blooming, Also particularly suitable for nitrosamine free systems

Moulded, Extruded, Calendered

DOG Products

Deogum 400 has been developed for the use in bisphenolic and peroxide cured FKM compounds to decrease the compound viscosity. It increases the extrusion and injection speeds with an excellent lubricating effect, even at low dosages. Deogum 400 leads futhermore to easier demoulding. Care must be taken higher dosages as hardness and compression set may increase

Primarily used for FKM, Improved demoulding and mould fouling behaviour, particularly when curing with peroxides improved dispersion and flow behaviour.

Moulded, Extruded, Calendered

DOG Products

Deogum 294 facilitates the processing of special elastomers as FKM, HNBR, ACM or ECO. Flow properties and moulding are improved by reduced Mooney viscosity. Deogum 294 eases the mould release and provides a smooth surface. The organosiloxane component in Deogum 294 is compatible with the elastomer and provides flow and release properties without the difficulties of a conventional silicone oil or silicone based additive

Primarily used for FKM, Improved release and flow behaviour, No impending influence of the organosiloxane on following processes.

Moulded, Extruded, Calendered

DOG Products

Deogum 194 facilitates the processing of special elastomers such as HNBR,ACM or ECO. Flow properties and mould fillings are improved by reduced Mooney viscosity. The combinationof additives in Deogum 194 is compatible with common elastomers. It optimizes the processing and release properties of the compound on the mixing devicesas well as in the downstream processes.

Improved release and demoulding behaviour, Low peroxide consumption, No impending influence of the organosiloxane on following process Also suitable for special elastomers such as NBR,ACM,ECO, etc.

Moulded, Extruded, Calendered

DOG Products

Deogum 80 acts as multipurpose processing additive, which can be used in broad range of elastomers. (e.g. EPDM, NBR, CR, HNBR) and acts as an internal lubricant. Deogum 80 achieves a clear flow improvement and facililitates the demoulding. In peroxide cross-linked compounds lower mould Fouling and better release effect are observed

Applicable for broad range of elastomers, Improved demoulding and reduced mould fouling in peroxide cured EPDM compounds

Moulded, Extruded, Calendered

DOG Products

Deoflow 821 is proven as an excellent mould release agent , is effective against mill sticking and has a positive influence on flow and release in the injection moulding process.

Lubricating and demoulding agent, Higher temperature stability, therefore also particularly suitable for NBR,HNBR, and ACM, Versatile areas of application, Low dropping point

Moulded, Extruded, Calendered

DOG Products

Universal processing additive for rubber compounds based on EPDM, NR, SBR and CR, in which zinc-containing processing additives could cause interferences, as well as for complex mouldings. Deoflow Z acts as lubricant and dispersing agent. Deoflow Z improves the flow properties and the release of the vulcanizates

Economical product Lubricating and dispersing agent Improves demoulding and release behavior.

Moulded, Extruded, Calendered

DOG Products

Deoflow D has a dispersing effect on fillers and improves the flow and extrusion properties of rubber compounds without having a peptizing or activating effect on vulcanization

Universally used since no side effects for vulcanization system. Optimised dispersion and flow behaviour. Economic product

Moulded, Extruded, Calendered

DOG Products

Deoflow A has a dispersing action on fillers and improves the flow and extrusion properties of rubber compounds without having a peptizing or activating effect on vulcanization

Universally used, since no side effects for the vulcanization system Optimized dispersion and flow behavior Free from metal ions and therefore also suitable for elastomers, which containing halogens

Moulded, Extruded, Calendered

DOG Products

Controzon Plus forms a flexible wax film on the surfaces of the vulcanizates and protects them from crack formation due to ozone attack under static conditions. It acts as a carrier for chemical ozone protecting agents and antioxidants and improves their effectiveness. The addition of about 2 phr prevents the ozone attack known as the frosting effect. Supplied as pellets, Controzon Plus is easy to handle and to weigh

For ozone tests between 40°C and 50°C, BfR / FDA suitable, Medium molecular weight distribution

Moulded, Extruded, Calendered

Robinson Brothers Products

1,1,3 Tributyl thiourea

Robac TriBTU is an active accelerator with some delayed action for mercaptan - modified polychloroprene (W-type NEOPRENE) The main application of TriBTU is an antiozonant for light coloured natural rubber and styrene butadiene rubber compounds, for example, white side walls, tyres, hoses,seals,footware and gloves. TriBTU activates the cure and the so cure systems will need modification. It can also be used in Nitrile rubber compounds It is a non -discolouring and non staining and is suitablefor use as an antiozonant in compounds in contact with paints

Moulding, Extruded, Calendered

Robinson Brothers Products

Tetrabutyl thiuram disulfide

Robac TBuT 60 is a liquid secondary accelerator, very soluble in hydrocarbon polymers. Low activity as a vulcanising agent. TBut 60 has the highest solubility in NR of any of the commercially available thiuram sulphides Used as a vital constituent is soluble E.V. Systems

Moulding, Extruded, Calendered

Robinson Brothers Products

Robac Delta PM is a proprietary blend of an activated dithiocarbamate

Robac Delta PM80 has been found to be particularly good technical equivalent for Tellurium diethyldithiocarbamate(TeDEC) in many EPDM cure systems TeDEC is under suspicion as hazardous when used in rubber manufacturing operations Robac Delta PM80 is highly cost effective and should be considered where risk and cost reductions are required Robac Delta PM80 is non - blooming under normal conditions of use

Moulding, Extruded, Calendered

Robinson Brothers Products

Di-isopropyl xanthogen polysulfide (active ingredient as 40% polymerbound masterbatch)

Robac AS100PM40SBR is used as a sulphur donor/accelerator in diene containing polymers (NR SBR IR IIR,among others where the avoidance in forming N-nitrosamines and type IV allergens are of prime concern. Product produced using AS100PM40SBR can be translucent and free from copper staining. Robac AS100PM40SBR synergies strongly with other accelerators

Moulding, Extruded, Calendered

Robinson Brothers Products

Di-isopropyl xanthogen polysulfide Chemical structure is completely free from nitrogen, phosphorous and metallic elements.

A FDA approved accelerator for use in NR, synthetic polyisoprene and NBR where formation of N-nitrosamines and type IV allergens from conventional accelerators are of prime concern. The vulcanisates obtained with AS100 are transparent and free from copper staining.

Moulding, Extruded, Calendered

Robinson Brothers Products

Replacement for Ethylene Thiourea ( ETU) and a safe alternative as an accelerator in polychloroprene rubber (CR) Vulcanisates cured with Robac SRM 102 give properties comparable to those cured with ETU.

Robac SRM PM 60can cure CR through a wide range of temperatures. Uncured rubber compounded with Robac SRM 102 have good storage stability at 40° C (bin stability, green storage) Using Robac SRM 102 PM 60 it is possible to reduce zinc oxide levels in CR cure systems without affecting the physical or rheological properties of the final vulcanisate. Many other rubbers can be cured with Robac SRM 102 PM 50 these include ECO, EPDM, NR. and CIIR

Moulding, Extruded, Calendered

Robinson Brothers Ltd Products

Zinc diisononyldithiocarbamate A higher alkyl dithiocarbamate of Zinc Recommended for use in the prevulcanisation of high ammonia natural rubber latex to minimise/overcome the concerns relating to health issues including N-nitrosamines and Type IV allergens.

Good transparency and colour of latex films is achieved using Arbestab Z, together with superior UV stability. Highly soluble in hydrocarbon polymers. Found to be an effective antioxidant in peroxide and radiation prevulcanised natural rubber latices.

Moulding, Extruded, Calendered

Emery Oleochemical Products

Solid, high molecular, multi-functional fatty acid ester (complex ester)

For PVC External lubricant with an optimal release effect and a lower dosage than of the products LOXIOL G 70 and LOXIOL P 621, Suitable in particular for the manufacture of highly transparent films For other plastics, By adding 0.2 to 5 % LOXIOL G 70 S to thermoplastic polyurethane, it is possible to release the moulded parts at a higher temperature without adhesion or sticking, which leads to an increase in productivity.

Moulded, Extruded, Calendered

Emery Oleochemical Products

Polyol partial ester

Phthalate free internal lubricant for PVC, Synergistic effect when used with CaZn stabilizers, LOXIOL G 62 facilitates mould filling and mould release in injection moulding, Due to this lubricant, additives such as pigments and fillers are best distributed in the polymer melt

Moulded, Extruded, Calendered

Emery Oleochemical Products

Saturated fatty alcohol

Internal lubricant, Improves the flowability of extrusion and injection moulding, compounds

Moulded, Extruded, Calendered

Emery Oleochemical Products

Neutral ester

Internal and external lubricant, Very good compatibility, Improvement of the non-tackiness, Suitability for transparent applications, Brilliant surfaces

Moulded, Extruded, Calendered

Emery Oleochemical Products

N, N'-ethylene-bis-stearamide

LOXIOL EBS P has proved successful as a processing auxiliary in a number of plastics. It is used to facilitate mould release of polyoxymethylene, thermoplastic polyurethane and synthetic- and natural rubber. It exerts a favourable influence on the flow and slip behaviour on polyolefins. LOXIOL EBS P is used as a lubricant in SAN. In ABS plastics LOXIOL EBS P improves flowability and thus thermoplastic processibility. To achieve certain properties, LOXIOL EBS P can be combined with other additives, e. g. with metallic soaps like LOXIOL EP 3500

Moulded, Extruded, Calendered

Emery Oleochemical Products

Mixture based on a polyglycol fatty acid esters

LOXIOL 3380 is a highly effective internal antistatic agent for several kinds of resins like PVC-P, NBR, H-NBR, NR, SBR, EPDM, PP, S/B, SAN, ABS, PA, POM, PMMA, PU, EVA and PUR. An appreciable reduction of surface resistance and increased surface conductivity are obtained

Moulded, Extruded, Calendered

Emery Oleochemical Products

Stearic acid of technical grade

External lubricant, Improved non-stickiness, Suitable for transparent applications

Moulded, Extruded, Calendered

Emery Oleochemical Products

Trimellitic ester of C8 and C10 linear alcohols

Extremely low volatility, Good thermal stability, Moderate low temperature properties (particularly after heat ageing), Good water resistance, Low migration into other polymers and rubbers

Moulded, Extruded, Calendered

Emery Oleochemical Products

Polymeric plasticizer based on adipic acid

The viscosity of Edenol 1208 is remarkably low therefore it can be used advantageously whenever highly viscous plasticizers are undesirable due to processing problems. Also due to the low viscosity, Edenol 1208 shows good properties in plastisol processing i.e. dipping and casting applications

Moulded, Extruded, Calendered

Emery Oleochemical Products

Plasticizer

EDENOL 181 is an effective plasticiser over a wide range of temperatures (-50 °C to +130 °C), Almost colourless liquid with a characteristic mild odour Readily miscible with most organic solvents Excellent low temperature properties (particularly after heat ageing) Good heat resistance (low volatility), Good compatibility with a wide range of rubbers

Moulded, Extruded, Calendered

Emery Oleochemical Products

Plasticizer

EDENOL 123 provides rapid processibility with many rubbers and has excellent compatibility even at high levels, Unlike most other low temperature plasticisers,Edenol 123 also provides resistance to microbial attack, Edenol 123 is miscible with most organic solvents

Moulded, Extruded, Calendered

Emery Oleochemical Products

Plasticizer

Excellent low temperature properties, Moderate heat resistance, Good compatibility with a wide range of rubbers, Effective over a broad temperature range between -52 °C and +120 °C

Moulded, Extruded, Calendered

Lehmann & Voss & Co Products

TAIC is a versatile crosslinking co-agent for peroxide or radiation crosslinking of synthetic rubbers and crosslinkable thermoplasts e.g. EPDM, EPM, EVA, FPM, FKM, Q, XPE, PA, PAN, PET, PVC, PMI polyimide-esters.

TAIC-cured vulcanisates show improved crosslinking density,compression set and enhanced heat resistance. Compared with other crosslinking co-agents. TAIC shows increased chemical inertness. Thus TAIC can be recommended for curing of high-mw-polymers under elevated temperature conditions. Process safety becomes significantly improved. Compared with pure TAIC the Dry Liquid improves handling and dosage, leading to better dispersion, optimum distribution of the active ingredient inside the compound.

Moulded, Extruded, Calendered